[En-Nut-Discussion] cannot compile basemon sample

[Thomas Bulckaert]

Hi, i am using Nut/OS 4.0.1 and ICCAVR v7.05
The board i am using is an Ethernut 1.3g

When i compile the project "basemon", i get the following error-report:
C:\iccv7avr\bin\imakew -f basemon.mak
iccavr -c -IC:\ethernut-4.0.1\nutbld-icc\include -IC:\ethernut-4.0.1\nut\include -Ic:\iccv7avr\include -e -D__ICC_VERSION="7.05" -D_MCU_enhanced -D__HARVARD_ARCH__ -DATMEGA -DATMega128 -l -g -Mavr_enhanced C:\ethernut-4.0.1\nutapp\basemon\basemon.c
!W C:\ethernut-4.0.1\nutapp\basemon\basemon.c: [warning] in function 'idle', argument 'arg' has no use.
iccavr -o basemon -LC:\ethernut-4.0.1\nutbld-icc\lib -g -ucrtatmegaram.o -bfunc_lit:0x8c.0x10000 -dram_end:0x10ff -bdata:0x1100.0x7fff -dFRAM:1 -dhwstk_size:16 -beeprom:0.4096 -fihx_coff -ucrtenutram.o C:\ethernut-4.0.1\nutbld-icc\lib\nutinit.o -S2 @basemon.lk -lnutpro -lnutfs -lnutnet -lnutos -lnutdev -lnutcrt -lnutarch -lcatmega
!E basemon.o(362): multiple define: '_NutInit'
!E basemon.o(389): multiple define: '_ms62_5'
want size 430
lo 65130 hi 65535 size 406
lo 65536 hi 65536 size 1
!E <library>(11792): area 'text' not large enough
want size 350
lo 65518 hi 65535 size 18
lo 65536 hi 65536 size 1
!E <library>(11792): area 'text' not large enough
want size 1132
lo 65518 hi 65535 size 18
lo 65536 hi 65536 size 1
!E <library>(11792): area 'text' not large enough
want size 290
lo 65518 hi 65535 size 18
lo 65536 hi 65536 size 1
!E <library>(11792): area 'text' not large enough
C:\iccv7avr\bin\imakew.exe: Error code 1
Done: there are error(s). Exit code: 1

I get almost the same results when i try to compile the httpd demo project. All the others work out fine. It looks like the error only occurs when there are files (like html pages) that need to be loaded in the chip, besides the program.

Has anyone seen this problem before? Yes, the chip is set on atmega128. I would really like to solve this problem, cause like this, i cannot start "playing" and "modifying" the webserver

I hope someone can help me.

Thanks in advance


Thomas Bulckaert
ORION ELECTRONIC SOLUTIONS
Ondernemingenstraat 3
8630 VEURNE
BELGIUM
0032 478 84 10 29
thomas at orionsolutions.be
http://www.orionsolutions.be

[James Mclellan]

Thomas,

I abandoned ICC-AVR v7.05 in favor of WinAVR.

I was getting problems similar to yours using board version 2.1.

Post by Thomas Bulckaert
Hi, i am using Nut/OS 4.0.1 and ICCAVR v7.05
The board i am using is an Ethernut 1.3g
C:\iccv7avr\bin\imakew -f basemon.mak
iccavr -c -IC:\ethernut-4.0.1\nutbld-icc\include -IC:\ethernut-4.0.1\nut\include -Ic:\iccv7avr\include -e -D__ICC_VERSION="7.05" -D_MCU_enhanced -D__HARVARD_ARCH__ -DATMEGA -DATMega128 -l -g -Mavr_enhanced C:\ethernut-4.0.1\nutapp\basemon\basemon.c
!W C:\ethernut-4.0.1\nutapp\basemon\basemon.c: [warning] in function 'idle', argument 'arg' has no use.
!E basemon.o(362): multiple define: '_NutInit'
!E basemon.o(389): multiple define: '_ms62_5'
want size 430
lo 65130 hi 65535 size 406
lo 65536 hi 65536 size 1
!E <library>(11792): area 'text' not large enough
want size 350
lo 65518 hi 65535 size 18
lo 65536 hi 65536 size 1
!E <library>(11792): area 'text' not large enough
want size 1132
lo 65518 hi 65535 size 18
lo 65536 hi 65536 size 1
!E <library>(11792): area 'text' not large enough
want size 290
lo 65518 hi 65535 size 18
lo 65536 hi 65536 size 1
!E <library>(11792): area 'text' not large enough
C:\iccv7avr\bin\imakew.exe: Error code 1
Done: there are error(s). Exit code: 1
I get almost the same results when i try to compile the httpd demo project. All the others work out fine. It looks like the error only occurs when there are files (like html pages) that need to be loaded in the chip, besides the program.
Has anyone seen this problem before? Yes, the chip is set on atmega128. I would really like to solve this problem, cause like this, i cannot start "playing" and "modifying" the webserver
I hope someone can help me.
Thanks in advance
Thomas Bulckaert
ORION ELECTRONIC SOLUTIONS
Ondernemingenstraat 3
8630 VEURNE
BELGIUM
0032 478 84 10 29
thomas at orionsolutions.be
http://www.orionsolutions.be
_______________________________________________
En-Nut-Discussion mailing list
En-Nut-Discussion at egnite.de
http://www.egnite.de/mailman/listinfo.cgi/en-nut-discussion

[Brett Abbott]

Thomas

Your compiler's func_lit parameter in the linker may be incorrect for
atmega128.

You have:

-bfunc_lit:0x8c.0x10000

Im using V6 of the compiler but I know many others are using V7.

My linker uses:
-bfunc_lit:0x8c.0x1e000

which reflects the 4K bootloader I use. (0x20000 is 128K)

Looking at the help in ICCAVR, this would suggest your compiler is only
aware of half the flash. If your code, with the flash file system you
are loading takes up more than 60K or so, you could expect the "want
size xxx" message which is an indication that the compiled code is too
big for the available space. The compressor may help but I suspect
there is another issue which is not allocating the correct size.

Im sorry but Im not sure whether the 0x1e000 is provided from nutos
config or ICCAVR settings. Perhaps the mightly Harald could help out
here ;)

Hope this helps with a few clues.

Goodluck
Brett

Post by Thomas Bulckaert

Post by Thomas Bulckaert
Hi, i am using Nut/OS 4.0.1 and ICCAVR v7.05
The board i am using is an Ethernut 1.3g
C:\iccv7avr\bin\imakew -f basemon.mak
iccavr -c -IC:\ethernut-4.0.1\nutbld-icc\include -IC:\ethernut-4.0.1\nut\include -Ic:\iccv7avr\include -e -D__ICC_VERSION="7.05" -D_MCU_enhanced -D__HARVARD_ARCH__ -DATMEGA -DATMega128 -l -g -Mavr_enhanced C:\ethernut-4.0.1\nutapp\basemon\basemon.c
!W C:\ethernut-4.0.1\nutapp\basemon\basemon.c: [warning] in function 'idle', argument 'arg' has no use.
!E basemon.o(362): multiple define: '_NutInit'
!E basemon.o(389): multiple define: '_ms62_5'
want size 430
lo 65130 hi 65535 size 406
lo 65536 hi 65536 size 1
!E <library>(11792): area 'text' not large enough
want size 350
lo 65518 hi 65535 size 18
lo 65536 hi 65536 size 1
!E <library>(11792): area 'text' not large enough
want size 1132
lo 65518 hi 65535 size 18
lo 65536 hi 65536 size 1
!E <library>(11792): area 'text' not large enough
want size 290
lo 65518 hi 65535 size 18
lo 65536 hi 65536 size 1
!E <library>(11792): area 'text' not large enough
C:\iccv7avr\bin\imakew.exe: Error code 1
Done: there are error(s). Exit code: 1
I get almost the same results when i try to compile the httpd demo project. All the others work out fine. It looks like the error only occurs when there are files (like html pages) that need to be loaded in the chip, besides the program.
Has anyone seen this problem before? Yes, the chip is set on atmega128. I would really like to solve this problem, cause like this, i cannot start "playing" and "modifying" the webserver
I hope someone can help me.
Thanks in advance
Thomas Bulckaert
ORION ELECTRONIC SOLUTIONS
Ondernemingenstraat 3
8630 VEURNE
BELGIUM
0032 478 84 10 29
thomas at orionsolutions.be
http://www.orionsolutions.be
_______________________________________________
En-Nut-Discussion mailing list
En-Nut-Discussion at egnite.de
http://www.egnite.de/mailman/listinfo.cgi/en-nut-discussion

_______________________________________________
En-Nut-Discussion mailing list
En-Nut-Discussion at egnite.de
http://www.egnite.de/mailman/listinfo.cgi/en-nut-discussion

[Brett Abbott]

Thomas

Your compiler's func_lit parameter in the linker may be incorrect for
atmega128.

You have:

-bfunc_lit:0x8c.0x10000

Im using V6 of the compiler but I know many others are using V7.

My linker uses:
-bfunc_lit:0x8c.0x1e000

which reflects the 4K bootloader I use. (0x20000 is 128K)

Looking at the help in ICCAVR, this would suggest your compiler is only
aware of half the flash. If your code, with the flash file system you
are loading takes up more than 60K or so, you could expect the "want
size xxx" message which is an indication that the compiled code is too
big for the available space. The compressor may help but I suspect
there is another issue which is not allocating the correct size.

Im sorry but Im not sure whether the 0x1e000 is provided from nutos
config or ICCAVR settings. Perhaps the mightly Harald could help out
here ;)

Hope this helps with a few clues.

Goodluck
Brett

Post by Thomas Bulckaert

Post by Thomas Bulckaert
Hi, i am using Nut/OS 4.0.1 and ICCAVR v7.05
The board i am using is an Ethernut 1.3g
C:\iccv7avr\bin\imakew -f basemon.mak
iccavr -c -IC:\ethernut-4.0.1\nutbld-icc\include -IC:\ethernut-4.0.1\nut\include -Ic:\iccv7avr\include -e -D__ICC_VERSION="7.05" -D_MCU_enhanced -D__HARVARD_ARCH__ -DATMEGA -DATMega128 -l -g -Mavr_enhanced C:\ethernut-4.0.1\nutapp\basemon\basemon.c
!W C:\ethernut-4.0.1\nutapp\basemon\basemon.c: [warning] in function 'idle', argument 'arg' has no use.
!E basemon.o(362): multiple define: '_NutInit'
!E basemon.o(389): multiple define: '_ms62_5'
want size 430
lo 65130 hi 65535 size 406
lo 65536 hi 65536 size 1
!E <library>(11792): area 'text' not large enough
want size 350
lo 65518 hi 65535 size 18
lo 65536 hi 65536 size 1
!E <library>(11792): area 'text' not large enough
want size 1132
lo 65518 hi 65535 size 18
lo 65536 hi 65536 size 1
!E <library>(11792): area 'text' not large enough
want size 290
lo 65518 hi 65535 size 18
lo 65536 hi 65536 size 1
!E <library>(11792): area 'text' not large enough
C:\iccv7avr\bin\imakew.exe: Error code 1
Done: there are error(s). Exit code: 1
I get almost the same results when i try to compile the httpd demo project. All the others work out fine. It looks like the error only occurs when there are files (like html pages) that need to be loaded in the chip, besides the program.
Has anyone seen this problem before? Yes, the chip is set on atmega128. I would really like to solve this problem, cause like this, i cannot start "playing" and "modifying" the webserver
I hope someone can help me.
Thanks in advance
Thomas Bulckaert
ORION ELECTRONIC SOLUTIONS
Ondernemingenstraat 3
8630 VEURNE
BELGIUM
0032 478 84 10 29
thomas at orionsolutions.be
http://www.orionsolutions.be
_______________________________________________
En-Nut-Discussion mailing list
En-Nut-Discussion at egnite.de
http://www.egnite.de/mailman/listinfo.cgi/en-nut-discussion

_______________________________________________
En-Nut-Discussion mailing list
En-Nut-Discussion at egnite.de
http://www.egnite.de/mailman/listinfo.cgi/en-nut-discussion

[Thomas Bulckaert]

Hi, i am using Nut/OS 4.0.1 and ICCAVR v7.05
The board i am using is an Ethernut 1.3g

When i compile the project "basemon", i get the following error-report:
C:\iccv7avr\bin\imakew -f basemon.mak
iccavr -c -IC:\ethernut-4.0.1\nutbld-icc\include -IC:\ethernut-4.0.1\nut\include -Ic:\iccv7avr\include -e -D__ICC_VERSION="7.05" -D_MCU_enhanced -D__HARVARD_ARCH__ -DATMEGA -DATMega128 -l -g -Mavr_enhanced C:\ethernut-4.0.1\nutapp\basemon\basemon.c
!W C:\ethernut-4.0.1\nutapp\basemon\basemon.c: [warning] in function 'idle', argument 'arg' has no use.
iccavr -o basemon -LC:\ethernut-4.0.1\nutbld-icc\lib -g -ucrtatmegaram.o -bfunc_lit:0x8c.0x10000 -dram_end:0x10ff -bdata:0x1100.0x7fff -dFRAM:1 -dhwstk_size:16 -beeprom:0.4096 -fihx_coff -ucrtenutram.o C:\ethernut-4.0.1\nutbld-icc\lib\nutinit.o -S2 @basemon.lk -lnutpro -lnutfs -lnutnet -lnutos -lnutdev -lnutcrt -lnutarch -lcatmega
!E basemon.o(362): multiple define: '_NutInit'
!E basemon.o(389): multiple define: '_ms62_5'
want size 430
lo 65130 hi 65535 size 406
lo 65536 hi 65536 size 1
!E <library>(11792): area 'text' not large enough
want size 350
lo 65518 hi 65535 size 18
lo 65536 hi 65536 size 1
!E <library>(11792): area 'text' not large enough
want size 1132
lo 65518 hi 65535 size 18
lo 65536 hi 65536 size 1
!E <library>(11792): area 'text' not large enough
want size 290
lo 65518 hi 65535 size 18
lo 65536 hi 65536 size 1
!E <library>(11792): area 'text' not large enough
C:\iccv7avr\bin\imakew.exe: Error code 1
Done: there are error(s). Exit code: 1

I get almost the same results when i try to compile the httpd demo project. All the others work out fine. It looks like the error only occurs when there are files (like html pages) that need to be loaded in the chip, besides the program.

Has anyone seen this problem before? Yes, the chip is set on atmega128. I would really like to solve this problem, cause like this, i cannot start "playing" and "modifying" the webserver

I hope someone can help me.

Thanks in advance


Thomas Bulckaert
ORION ELECTRONIC SOLUTIONS
Ondernemingenstraat 3
8630 VEURNE
BELGIUM
0032 478 84 10 29
thomas at orionsolutions.be
http://www.orionsolutions.be

[James Mclellan]

Thomas,

I abandoned ICC-AVR v7.05 in favor of WinAVR.

I was getting problems similar to yours using board version 2.1.

Post by Thomas Bulckaert
Hi, i am using Nut/OS 4.0.1 and ICCAVR v7.05
The board i am using is an Ethernut 1.3g
C:\iccv7avr\bin\imakew -f basemon.mak
iccavr -c -IC:\ethernut-4.0.1\nutbld-icc\include -IC:\ethernut-4.0.1\nut\include -Ic:\iccv7avr\include -e -D__ICC_VERSION="7.05" -D_MCU_enhanced -D__HARVARD_ARCH__ -DATMEGA -DATMega128 -l -g -Mavr_enhanced C:\ethernut-4.0.1\nutapp\basemon\basemon.c
!W C:\ethernut-4.0.1\nutapp\basemon\basemon.c: [warning] in function 'idle', argument 'arg' has no use.
!E basemon.o(362): multiple define: '_NutInit'
!E basemon.o(389): multiple define: '_ms62_5'
want size 430
lo 65130 hi 65535 size 406
lo 65536 hi 65536 size 1
!E <library>(11792): area 'text' not large enough
want size 350
lo 65518 hi 65535 size 18
lo 65536 hi 65536 size 1
!E <library>(11792): area 'text' not large enough
want size 1132
lo 65518 hi 65535 size 18
lo 65536 hi 65536 size 1
!E <library>(11792): area 'text' not large enough
want size 290
lo 65518 hi 65535 size 18
lo 65536 hi 65536 size 1
!E <library>(11792): area 'text' not large enough
C:\iccv7avr\bin\imakew.exe: Error code 1
Done: there are error(s). Exit code: 1
I get almost the same results when i try to compile the httpd demo project. All the others work out fine. It looks like the error only occurs when there are files (like html pages) that need to be loaded in the chip, besides the program.
Has anyone seen this problem before? Yes, the chip is set on atmega128. I would really like to solve this problem, cause like this, i cannot start "playing" and "modifying" the webserver
I hope someone can help me.
Thanks in advance
Thomas Bulckaert
ORION ELECTRONIC SOLUTIONS
Ondernemingenstraat 3
8630 VEURNE
BELGIUM
0032 478 84 10 29
thomas at orionsolutions.be
http://www.orionsolutions.be
_______________________________________________
En-Nut-Discussion mailing list
En-Nut-Discussion at egnite.de
http://www.egnite.de/mailman/listinfo.cgi/en-nut-discussion